denon avr 3300 service manual

The System Setup Menu reappears. ENTER Select “ON” or “OFF”.Level” screen. Select “Vol. Level”. Enter the setting. The “System Setup Menu” reappears.Furthermore, it is equipped with a function for learning the control signals of remote control units of other manufacturers, so it can also be used to operate non-DENON remote control compatible video components. DECK VDP VCR Operate the audio component. Operation is not possible for some models, however. In this case use the learning function (see page 34) to store the remote control signals. This function can be used to turn on the amplifier’s power, select the input source, turn on the monitor TV’s power, turn on a source component’s power and start playback, etc., all at the touch of a button. To clear “learned” remote control signals, set the slide switch to the position at which the signals were “learned”. To clear the preset memory settings, set the slide switch to “VIDEO”. Example: Stereo SELECT (Main unit) The tone switches as follows each time the TONE CONTROL button is pressed. TONE CONTROL (Main unit) With the name of the volume to be adjusted selected, turn the SELECT knob to adjust the level. Press the VIDEO SELECT button repeatedly until the desired source appears on the display.This operation is not possible in the “8CH IN”. FUNCTION (Main unit) w Set the input mode to “AUTO”. One of six preset surround modes can be selected according to the program source and the parameters can be adjusted according to the conditions in the listening room to achieve a more realistic, powerful sound. Select the surround mode for the input channel. (Remote control unit) The surround mode switches in the following order each time the DSP SIMULATION button is pressed: MONO MOVIE ROCK ARENA MATRIX. Display the surround parameter screen on the monitor. The screen for the selected surround mode appears. There are five settings: “small”, “med.s” (medium-small), “medium”, “med.l” (medium-large) and “large”.

• denon avr 3300 service manual, denon avr 3300 service manual pdf, denon avr 3300 service manual, denon avr 3300 service manual, denon avr 3300 service manual download, denon avr 3300 service manual pdf, denon avr 3300 service manual free, denon avr 3300 service manual software, denon avr 3300 service manual.

Be sure to keep this manual for future reference should any questions or To be sure you take maximum advantage of all the features the AVR-3300 has to offer, read these instructions carefully and use the set properly. Be sure to keep this manual for future reference should any questions or problems arise. This remarkable component has been engineered to provide superb surround sound listening with AV theater sources such as DVD, as well as providing outstanding high fidelity reproduction of your favorite music sources. Incomplete connections will result in the generation of noise. Remove the vinyl tie Bend in the reverse and take out the direction. Mismatching of polarities will result in weak central sound, unclear orientation of the various instruments, and the sense of direction of the stereo being impaired. Display the System Setup Menu.ENTER b) If both surround speakers A and B are used (if either “Large” or “Small” is set for both A and B): The surround speaker setting screen appears. ENTER Select the bass signal playback mode. Enter the setting. The System Setup Menu reappears.ENTER Select the desired unit, meters or feet. Select (darken) the desired units, “Meters” or “Feet”. Once “Meters” or “Feet” is selected in step 3, the Delay Time screen appears automatically. Select the speaker to be set. Set the distance between the center speaker and listening position. ENTER The AVR-3300 automatically sets the optimum surround delay time for the listening room.Select “Yes”. a. If the “Auto” mode is selected: Test tones are automatically emitted from the different speakers. The test tones are emitted from the different speakers in the following order, at 4-second intervals the first time and second time around, 2- second intervals the third time around and on: Use the CURSOR buttons to adjust all the speakers to the same volume. At the System Setup Menu select “Digital Inputs”. Switch to the Digital Inputs screen. ENTER Enter the setting.

You should upgrade or use an alternative browser. I need it for a friend of mine who is having some trouble with it.How can i help. Pat Mine just broke down I love This amp. So i am desperite !! Thanks in advance I Googled this model and several folks had problems, (Wont pwr up just a relay clicking) But I've got my fingers crossed Thanks We have talked about this unit, (how much everybody has had trouble with this POS) and it's been put on the back burner. I can't believe how much i use to brag on Denon. I've got a newer model( MADE IN CHINA) from a local shop. What a piece of junk.I went to srvman and couldn't find it, So i Googled it for something similar,(couldn't find anything, I thought manufacturers made a series of similar models???) so tried to down load a 685. How do you use the coupon??? Sorry to bug ya, Thanks again I should've did my homework and found a similar model.Thanks for the offer though I really do appreciate it. Hope i can get an offer like that again.How can i help. PatI've got a Denon avr-3300 which doesn't power up at all. I'm very electronics savvy, but would rather not have to take the main board out to trace out the circuit to find out why I have power at the fuses but why not further. I am looking for a service manual with schematics or just schematics and ran across your thread. I know this is a longshot, but is is possible that you still have it.Let me know, and thanks. Join the AVForums team live on Sundays at 7pm. It contains circuit diagrams ( schemas ) etc. It also usually contains parts catalog. See below for delivery information The manual is available only in language(s): English Will do business with this vendor again. Some scanned pages are not perfectly square, but that is a minor complaint. The document schematics and board diagrams are easy to read, of good contrast. The whole file downloaded quickly. This is a good service. It is still available through their print-on-demand pro parts system, but why would you do that?

“small” recreates a small sound field, “large” a large sound field. EFFECT LEVEL: This sets the strength of the surround effect. The level can be set in 15 steps from 1 to 15. Press the MEMORY button. (Remote control unit) Press the SHIFT button and select the desired memory block (A to E). (Remote control unit) Press the PRESET UP or DOWN button to select the desired preset channel (1 to 8). Watching the display, press the SHIFT button to select the preset memory block. (Remote control unit) Watching the display, press the PRESET UP or DOWN button to select the desired preset channel. If this unit is not operating properly, check the items listed in the table below. This means that you can connect a pair of bipolar or dipolar surround speakers (mounted on either side of the prime listening position), as well as a separate pair of direct radiating (monopolar) speakers placed at the rear corners of the listening room. Dolby Surround (1) Dolby Digital (Dolby Surround AC-3) Dolby Digital is the multi-channel digital signal format developed by Dolby Laboratories. Set the surround mode to “DOLBY SURROUND” (see page 45) to play in Dolby Pro Logic. All files are provided under strict licence and reproduction without prior permission or for financial gain is strictly prohibited. If you have additional documentation please consider donating a copy to our free archive. To purchase AVR-3300 spares or accessories, please contact the company via their website or visit an authorised retailer. Service manuals usually include printed circuit boards, block diagrams, exploded views, assembly instructions and parts catalog. It's invaluable source of information for everyone looking to repair their unit. You should look for Owner's Manual. After placing order we'll send You download instructions on Your email address. For a better experience, please enable JavaScript in your browser before proceeding. It may not display this or other websites correctly.

If you don't follow our item condition policy for returns, you may not receive a full refund. Refunds by law: In Australia, consumers have a legal right to obtain a refund from a business if the goods purchased are faulty, not fit for purpose or don't match the seller's description. More information at returns. All Rights Reserved. User Agreement, Privacy, Cookies and AdChoice Norton Secured - powered by Verisign. This is the exact same technical repair manual which is used by all certified Denon technicians and professional repair shops. After your payment you will instant access to download this manual so you can start doing your repairs within a matter of minutes. Specifications: Language: English Format: PDF Page: 208By continuing to use this website you are giving consent to cookies being used. Please use the previous link instead. Select a product Please use the previous link instead. Select a category Please follow this FAQ to fix the issue. Please consider reviewing our FAQs to see if your inquiry is covered and don’t forget to check our YouTube channel for setup and installation videos. We apologize for the inconvenience and appreciate your patience during this challenging time.All hours are Eastern Standard Time. If you continue without changing your cookie settings, we'll assume that you are happy to receive all cookies on our website. However, if you would like to, you can change your settings at any time using the Change cookie settings link in the Special menu. Anyone who has bought before can download the updated package on request for free. All news Please enable JavaScript in your web browser. And by having access to our ebooks online or by storing it on your computer, you have convenient answers with Denon Avr 3300 Manual Download. To get started finding Denon Avr 3300 Manual Download, you are right to find our website which has a comprehensive collection of manuals listed.

Thank You. Rick. Cincinnati, Ohio. You will receive a unique download link via Ebay mail. All of these ” You will receive a unique download link via Ebay mail. All of these manuals are the official documents as used by all authorized Denon technicians and maintenance employees. ”. We have 40 Denon Diagrams, Schematics or Service Manuals to choose from, all free to download.This Website contains a compilation of information already available elsewhere on the internet and therefore considered to be in the public domain. We make every effort to ensure the information contained here is as accurate as possible, but we will not be responsible for any errors or omissions, or anything resulting thereof. However, we do not accept any liability for any loss, damage or inconvenience, of any kind, as a result of downloading any information from this site. Always scan any information downloaded from the internet with an up to date virus scanner before opening the downloaded information. Something went wrong.Learn more - opens in a new window or tab This amount is subject to change until you make payment. For additional information, see the Global Shipping Program terms and conditions - opens in a new window or tab This amount is subject to change until you make payment. If you reside in an EU member state besides UK, import VAT on this purchase is not recoverable. For additional information, see the Global Shipping Program terms and conditions - opens in a new window or tab Delivery times may vary, especially during peak periods. Learn more - opens in a new window or tab Learn more - opens in a new window or tab Learn more - opens in a new window or tab Learn more - opens in a new window or tab Learn more - opens in a new window or tab Contact the seller - opens in a new window or tab and request a postage method to your location. Please enter a valid postcode. Please enter a number less than or equal to 2.

Pop the IC back into the socket, check orientation and reattach the cover. Slide the cover closed. This was very tricky for me and I actually had to slightly file the upper edges of the socket cover before IYou can skip this step if youReconnect the DSP card and make sure it is seated properly. Reattach the plastic card spacers.Secure the backplate. Remember to resolder the capacitor leg if you had to desolder it in step 3.Reattach the covers and cables.Turn the power on. and pray that it works.:-)If the fix worksAs for the fan. I didn't do anything about it as of yet. I'll keep an eye on it and if it still refusesI'm leaning on theThis is probablyMany electrical contact issues can be localised by simply physically wiggling things around. And a multimeter helps you find out if the components are operating at correct voltages.I have the same problem on my AVR-3300 (1 corner was cracked). I am going to resolder all 4 corner. I do have another question. When I play DVD, my AVR-3300 will alway take audio input from the digital coaxial input. Do you know how I can switch to take input from one of the digital Optical inputs. I lost my manual for my AVR-3300.You can change digital input settings from system setup (System setup button on the remote). You'll need to connect the receiver's monitor out to your TV to see the menus. Denon has the manual for AVR-3300 on their website as a free download: I'm no electronics guru, but I know how to solder and I managed to fix my AVR 3300 today thanks to your article and the detailed photographs. So once again, thanks a lot. I felt that if I could be of help to even one AVR-3300 owner struggling with the DSP glitch this article would be worth the time spent writing it. But two so far. fantastic! Speaks a lot about the audio quality of the AVR-3300 that people are still using it after 10 years despite its problems and the rapid speed of development on the digital audio front. I hope it works.

In my reciever there are not cracked corners, neither is applying pressure fixing the sound issues. I dont know if we have the same problem, but basically sound works from analog inputs, but not from digital. None of the optical or coax inputs produce sound (except garbled static and crackles) and I figured it had to be the DSP. Do you think there may be something else (i.e. with the PCB containing the optical inputs)???? Thank you so much I took apart and re-soldered the IC (it wasn't cracked or seperated in any way but I did this anyways) and this did not fix the problem. I am now searching the DSP for any other faults and cannot find any. I came to realize it is not my optical which is bad because I can be going through analog DVD input and the sound works perfect, but once I switch it to 2 channel dolby (through analog) it immediately cuts to static and crackles. Any other suggestions from your experiences of what could be wrong. Maybe my IC is just a bad chip I dont know. In the last case there really isn't anything you can do. As it is the digital inputs that don't work correctly it is probable that problem lies somewhere on the DSP card or on the digital input card (as you've already figured out). This is what I'd do: With the power on and digital input selected (you're hearing static from the speakers) use a can of cold spray meant for electrical troubleshooting to find out if cooling any single component on the DSP or digital input card will affect the sound. You can also use something non-conductive (eg.Find out if the sound changes. If it does, concentrate on that area and narrow down the affected component. Also, wiggle the whole DSP and digital input cards and see if that has any effect. If you see any electrolytic capacitors that are visibly swollen or leaking they can be the culprit. A good electrician's rule is to always keep your other hand behind your back when poking aroung live devices so you won't accidentally stick it where it shouldn't go.

Our library is the biggest of these that have literally hundreds of thousands of different products represented. I get my most wanted eBook Many thanks If there is a survey it only takes 5 minutes, try any survey which works for you. If so, please let us know and we'll be happy to assist! The selected input modes for the separate input sources are stored in the memory.The presence or absence of digital signals is detected, the signals input to the digital input jacks are identified and decoding and playback are performed automatically in DTS, Dolby Digital or PCM (2 channel stereo) format. If no digital signal is being input, the analog input jacks are selected.Login to post I bought the unit around 2007. You can find the specifications for the AVR-887 in the manual. ManualsLib has the manual here. The specifications are listed here. The page with the monitor connection is. I hope this helps. Cindy WellsAny thoughts? See the address sheet included in the box. 1-855-MY.DENON 1-855-693-3666 Call for Assistance: 9:00AM to 8:00PM M-F E.S.T Denon AVR 3313CI Owner Manual Denon AVR 2313CI Specification How do I reset? Would have to be servicedI'm not sure if they will sell them to the public. We used to get them as a Denon service center. What is the specific problem you are trying to resolve. Perhaps with a description we can guide you through the repair. DanI bought the unit around 2007. Answer questions, earn points and help others. And this device delivered. I personally fell in loveSome people findThe two mainWhen I got my. AVR-3300 it only worked for a few days before the DSP card failed. I had to wait forThe second unit worked fine for six months or so beforeFinally in early 2009 the sound started cutting off completely in allNow I really had to do something about it.And isn't it more ecological (ooo, trendy) and economical (bad times, baaad times)This was very troubling as the.

DSP card (Denon part number 1U-3215) costs between USD 500-850 even if you can find it Some further information hunting led me to a discussion on DSP card.The first one was that the fan would never startSome quick measuring didn't reveal any immediate problem with the cooling fan as the fan itself seemed to work fineI assume the fault lies within one of theThis is probablyIt seems that due to bad design the socket is under constant stress from a combination of There are hazardous This is all pretty obvious of course but pleaseThese instructions assume your AVR-3300 is actually suffering from a problem caused byIf it is not. sorry, I have no answers: Maybe you'll be betterDisconnect all the cables and remove the covers. There are three screws on both sides and three at the back.Familiarise yourself with the parts inside. The main parts are indicated in the following picture.Check if the audio dropping problem is the result of the sameYou can also try using some cold spray or gentlyIf you're convinced the fault is similar to mine, continue on to step 4.Remove enough of the screws holding the backplate in place to bend it 1-2 cm (0.5-1 inch)Or you can remove the whole backplateNote: one of the screws You'll have to desolderThe shiny screw is soldered toRemove the DSP card by pulling it straight up. It might be a bit hard to remove but it'llLocate IC403 and open the socket cover by sliding it to the direction indicated by an arrow. RemoveAvoid touching any of the IC or socketThe cover might not be easy to slide but you'll get there. Also, if the ICIf you lookKeep some weight on the socket so that it stays in contact with the PCB and resolder at least the cracked corner pads. I resoldered all the corners just to be on the safe side. I used a little extra solder in order to secure the However, make sure you don't use too much solder and cover the smallWhile you're at it, checkGently clean the connecting foils of the socket and IC with isopropyl alcohol.

If you're even remotely unsure about diagnosing the device with the power cord attached, don't. Doing the wrong thing can kill you. I had exact the same problem. I followed the instructions and repaired my AVR 3300. Greetings, Marcel Blokland I hope you get many more years of use out of your Denon. My Denon AVR-3300 has shown both the noisy fan and DSP problems. Interestingly the fan noise seems to be gone now after many years - maybe the fan is totally broken now. The DSP problem has happened a few times (distorted sound when using onboard DACs) but seems to be OK for the moment. What is the purpose of the fan. To cool the DSP card. To cool the power amp stage. Or to cool both? If the fan doesn't work anymore, what will happen. I would like to hear your thoughts. By the way, I think the AVR-3300 is a nice sounding unit and worth saving! There's also some internal logic to control the speed of the fan depending on the sound output to the speakers: in quiet parts the fan speed is automatically reduced. The idea is that the fan should never be audible over the sound played by the device. However, as you've already suffered from a noisy fan before, it is possible that the fan has failed completely. The only way to be sure would be to open the amplifier and test the fan. I wouldn't be too worried though because if the device gets too hot (with fan or not) it should simply shut down to protect itself. If that hasn't happened it should still be within safe operating temperatures. The fan's main purpose seems to be to cool the amplifier stage: all the power ICs are in contact with a big tunnel-shaped heatsink through which air is blown with the aid of the fan. Some of the air sucked in goes past the DSP card but the card itself or the components on it don't seem to get too hot by themselves.

One end of the DSP card (where the troublesome IC socket is located) is right next to the cooling fan and my theory is that the constant cooling and warming caused by the fan turning on and off causes enough thermal expansion to eventually brake the soldering on the socket. In other words, poor design. Yes, poor design seems to be case. I believe that Denon abandoned fan cooling with their later models. Another problem I have with my unit is that the on-screen display output to my TV is blurry with horizontal lines scrolling down. Would this problem be related to the DSP card, or is there a specific video card in the unit? Video output problems can be caused by many things such as ground loops and bad cables. I personally only use the composite out for setup and even that very rarely. You can try pulling out all the other audio and video cables from the amplifier and your tv (as well as the aerial cable) and see if you still get the same problem. If it works connect the cables back one at a time and see which one causes the problem to reappear. I recall having similar distortions in the picture when my computer was connected to the amplifier as well as to my television. If you're using composite out try using s-video or component and vice versa. See if it makes any difference. Ground loops can be difficult to diagnose and fix. Your video problem probably has little to do with the DSP card. The components responsible for video are located on three separate cards. Two of the cards (composite and s-video) are between the DSP card and the cooling tunnel and the third one (component) is the topmost board on the other side of the cooling tunnel. Simply put, the relevant video connectors on the back of the amplifier are directly connected to the cards in question. At the moment I am not using the Denon for any video switching and like you I am only using the composite output for set-up - although even this is not pleasant given the blurry picture.

I'll be getting out the trusty soldering iron when I have a free hour or two and solder those corners. Cheers from Australia!! Was getting ready to go buy a new one.It looks like someone has tried soldering a corner leg but failed and bare copper is showing like it's been flipped over. Are all of these supposed to have a socket. Also the guy selling the 3300 said the fan came on while there but it has yet to come on here. How hot does the heat sink get before it comes on, almost hot enough to burn your fingers. Thanks for the great tut. Nice to know about the audio issues and possible fix for these, however I have never got any problems with DSP. Some poor soldering with capacitors caused 100 Hz mains hum some years ago. That's the only fault alomg with fan. I have had the AVR3300 about ten years for now. The whining sound is caused by the fan motor. The design of the fan control circuit is poor because it doesn't include proper starter circuit to generate a pulse which kicks the fan on. So the voltage in fan terminal raises slowly. Many of these type of fans whine when they are trying to start but there's not enough volts. Some of the fans rotate their blades back and forth, making a clicking sound. I'm pretty sure that easy solution for the fan noise could be to replace the fan with some other model. It looks like standard 80x80 mm.But I'm not sure if it has 12V motor. Currently I have no idea which fan would be good here. Possible some PAPST model could be the one which starts properly even with low voltages without whining. Only way to find one is to test different fans with adjustable power supply and see how they act with low voltages. It also would be nice to know how they fix that fan problem in the warranty repair. Dan: I just check the IC403 from the service manual and it's the flash memory holding the DSP software. So there MUST be a socket for it, otherwise it's quite hard to update the DSP software.

That's infact also a kind of poor design: there's no possibility for ISP (In Circuit Programming) so you have to take the chip out for any updates - just like EPROMS in the 80's hardware. My unit's fan problem was fixed by simply replacing the fan with a new (generic) one under warranty. Nothing else was done to it. The fan is a 80x80 mm 24 volt model. I agree that some Pabst 24 V model would be a good replacement. Dan: Yes, there should be socket for IC403 -- or at least there has been one originally. Also, the heat sink gets REALLY hot before the fan even considers starting. You will burn your fingers.:-) Thanks for your kind and informative comments everyone. Maybe you can help me as well. I'm unaware if the problem I'm having is the same but, for whatever reason, when I connect analog speakers to the front pre outs I get static through them, even without a source connected. This doesn't happen if I move the same speakers previously in the front pre outs to the surround pre outs (either A or B). Any suggestions? Thanks for any information you can provide. If I understand you correctly you are connecting speakers straight to the pre-outs without an amplifier: that won't work unless you have active speakers. The pre-outs are meant to be used as input to an amplifier which in turn drives the speakers. Speakers should only be connected to the speaker terminals. I couldn't see any sign of cracked solder on the pads, but added some fresh anyway. Maybe removing and re-fitting the card actually helped, but either way you've given my beloved amp a stay of execution and saved me a bundle of cash. Many many thanks! During my first attempt to repair I resoldered the socket corners as described but did not clean the DSP and socket contacts. This did not solve the problem. After re-reading this thread I made a second attempt to repair, this time only removing the DSP and thoroughly cleaning all contacts with electrical parts cleaner.

This seems to have solved the problem and the unit has been working flawlessly for about three weeks now. My suspicion is that the IC and socket contacts had oxidized; once properly cleaned the unit began working again. Thanks again and hope this helps other AVR-3300 users! I bought the AVR3300 off the gray market and had no problems (except the fan, like everyone else it seems) until late 09. The repairman I gave it to gave up when DENON told him the card was NLA (No Longer Available?). The 2 corners nearest the end where the ID is labeled are cracked on mine and I am handy with a soldering iron so will have this resoldered today. Again, thanks for such clear diag and instructions. Judging by the comments this DSP problem really is widespread. Eric B: I'm delighted to hear you managed to fix your AVR-3300. It seems that the contacts between the IC and the socket are as much a part of the problem as the socket soldering. Recently I had to open my own AVR-3300 again as I started to experience the same old problems. I cleaned the IC contacts and very carefully bent them so that they apply more pressure against the socket and everything was fixed once more. Erik W: Good luck and I hope you'll get yours fixed. Yes, as far as I can tell the DSP card is no longer available from Denon. We are on our own. The unit sat in the corner for ages. I pulled it out after finding your page - and tapping on the IC makes the sound come on. Wow - yippee. Gonna polish the unit back up and put it back on the rack. Unfortunetly I upgraded to a new amp a while back with all the latest gadgets. But glad to have the old unit come back to life. Wonderful write-up. And thank you again. Regards Ken I had this problem long time ago, when I just got it. I am guessing they spoke of the same chip. Now the problem is back.Will try what you described here. Aleks, your problem sounds like it could very well be the exact same problem described on this article.